![]() ![]() 2.The camera will be exposed to high risks of motherboard damage and void the warranty if you use passive PoE injector/splitter at 30W AC V in Active PoE injector 48V 0.5A DC out PoE (cat5/5e/6) Active PoE splitter DC12V out RJ45 out RJ45 in Active PoE Injector/Splitter are allowed if you use PoE to power non-poe cameraĦ 2.2 For PoE+ Camera : PoE+ IEEE 802.3at standard is required, Note traditional PoE system( af standard) delivers up to 15.4W, which is unable to fully support the camera. Risk Relevant 1.Using 24VAC or higher voltage adapter (16V, 24V) will immediately dam-age the camera and void the warranty. For extension, you can select from AC power extension cable (no distance limit) or thick ( 18 AWG) DC power extension cable. If that happens, please make your AC power source near the camera, and connect it with our default adapter you received from the package. ![]() 2.1 For Non-PoE Camera (if you extend the power): The camera may not work properly if the power reaches the camera is be-low 12V due to resistance along the extended DC line (distance depend-ent). So do NOT pull the old setup from your bullet and apply it directly to your new PTZ. Now I just need to pick the right extension cable and mount it outside! Injector/Swith 100V~250V POE+ 30W Data out POE+out 100~250ft Wiring method: ELV (Extra-LowVoltageSystem) Router POE at Data inĥ 100V~250V Power Adapter Extended AC Line Data in DC 12V Non-PoE Wiring method: ELE (Force Electricity) Router 2.How to power the camera There is an old saying that PTZ cameras are POWER-ful. Questions? Ask Phase 2: Mounting Outdoor Good, the camera is working correctly. Connection Good Power Good Video and Control Good Tested Day and Night Guess we are ready to mount it outside. Ple-ase refrain from disassembling the unit before contacting us. Please contact our technical staff if a self-test does not happen on your unit. Built-in self-test When powered up, the speed dome automatically begins a self-diagnostic process during which the camera will pan horizontally and vertically to make sure PTZ, lens and other parts of the camera are functional. Underpower cau-ses problems such as 1) flickering screen 2) unstable infrared (camera reboots repeatedly) and 3) spinning dome. A bench test helps you rule out all problems caused by power supply. Secondly, if the camera cannot be found by connecting to the router, please try connecting it to the Ethernet port on the computerĤ Why Test Locally The reason you should NOT extend the power cable during the bench test is because DC power drops quickly along the transmission. Please connect the camera directly to the power adapter. How to Test Locally In short, in a bench test, do NOT use any power extension cable. If the camera works properly under the DC power adapter but not with PoE, please check the PoE switch/injector you are using or replace an Ethernet cable. PoE+ camera A default adapter is prepared for you to rule out any problems of the cam-era. Please directly apply the DC12V adapter on the camera to make sure the unit itself is working, and try eliminating all cabling factors to set up the bench test. Therefore, how the unit is powered can be critical to its functionality. Camera Connection Phase 1: Bench Test ALWAYS test and setup locally before mounting outside! Adapter DC12V * * What are you testing in this stage? Non-PoE camera Note PTZ dome cameras have much higher power requirements than bullet cameras, especially for ones with higher zoom-in capacity. Stay at least 24 hours to test both daytime and night vision IR LED. WARNING: Please test the camera locally by directly connecting to the default power adapter from the package before mounting it outside. The operation of the device is thus limited by the following two conditions: 1) it is not permitted to cause harmful interference to any authorized radio communications, and 2) it must accept any interference it receives. 1 2017/04 Version 4.0 Dedicated PTZ Camera Professional SUNBA PTZ Camera Network Series User Guide V4.0 Please go to to access the step by step YouTube video tutorials for Sunba IP PTZ camera setup.Ģ FCC Warning (U.S.A) The device has been tested in compliance with limits set by Part 15 of Federal Communication Commission (Class B).
0 Comments
Leave a Reply. |